Registration of battery replacement in BMW E series cars

Description

Why do you need to prescribe a battery?

This is what the IBS sensor looks like

Registration of battery replacement using INPA

You can also register a replacement through DIS:

Registration of battery replacement through the Tool32 program

How to replace battery characteristics by coding with NCS Expert

 

Registering a battery replacement is an important step in the maintenance of a BMW car. This is due to the fact that the battery is a key element of the car's electrical system and its replacement can affect the operation of other systems.

In BMW vehicles from 2002 and newer, it is necessary to register the replacement of the battery in the vehicle control system to ensure the correct operation of the electronic systems and avoid possible problems.

You can use special software or tools such as a car scanner or a vehicle diagnostic interface to register battery replacements in BMW vehicles. Usually, the registration of battery replacement can be carried out in specialized service centers that have the necessary equipment and experience to carry out this procedure.

Registering the replacement of the battery in BMW cars helps to ensure the correct operation of electronic systems and avoid possible problems with the car. This procedure allows the car management system to adjust the optimal parameters for the new battery and take into account its characteristics during the further operation of the car.

If you have any problems with the battery in a BMW car or need to register a replacement, contact experienced car repairers or specialized service centers. But, if there is a desire to do it yourself, then this article-instruction is for you.

For BMW (E65, E66, E67, E60, E61, E63, E64, E81, E87, E90, E91, E92, E93, E70, R56) it is not enough to replace the battery, you must also register in the battery replacement system. But it should be noted that this procedure applies only to cars with IBS (intelligent battery sensor).

One of the main tasks of the IBS sensor is to extend the service life of the battery . Therefore, ordering a new battery will extend its life and save you money in the future.

But do not forget that only AGM batteries should be installed on these cars.

 

This is what the IBS sensor looks like

 

If you install a new battery without registering it, then an error will appear on the on-board monitor: Recharge the battery (Recharge Battery). But why? After all, a new battery. This is with outdated data in the control unit. This applies to E65, E66 and E67 bodies.

If you bought a new battery with identical characteristics to the previous battery, you only need to register the replacement. But if you decide to install a battery in which the type and capacity differ from the previous one, then you will need to make changes to the characteristics by coding.

Registration of battery replacement using INPA:

1) Open the INPA application;
2) Choose the required body;
3) Select BODY in the menu
4) Next, in this section, look for the POWER MODULE item
5) Press ACTIVE and then ACTIVATE2
6) Now you need to press F7 on the keyboard - Register battery replacements
Next, the "Register battery replacement Activated properly" window will open

 

You can also register a replacement through DIS:

1) In the application, select the BODY section
2) Next is the Power Supply division
3) Now click on Battery
4) The Register Battery Change line appears

 

Registering a battery replacement through the Tool32 program:

1) Open the application
2) Next, a window appears where you need to select your ECU file (example: msv70.prg)
3) In the left column we find steuern_batterietausch_registrie
4) Now click Start Job on the toolbar

Battery replacement successful!

 

Now we will tell you how to replace the characteristics of the battery by coding

 

For this we need the NCS Expert program

1) Replacement of battery indicators
2) Open the program
3) Select a profile
4) Press F1 on the keyboard
5) Then press F3 and look for the required body in the list

6) Select the body and press OK
7) Next, select CAS
8) And press the F6 key
9) Now select Process ECU (F3, for old versions – F4)
10) Select the block - CAS
11) Press Change Job (F2) and select "CODIERDATEN_LESEN" in the list that appears
12) Now press Execute Job (F3).
13) The FSW_PSW.TRC file has been updated in the WORK folder
14) Open this file using Notepad and transfer all contents to another file - FSW_PSW.MAN
16) Find the KLASSE_BATTERIE line and change the values to the ones we need: 110ah, 90ah, 80ah, 70ah, 55ah, 46ah. For AGM: 90ah_agm, 80ah_agm, 70ah_agm, 60ah_agm, 40ah_agm.
17) The last step. Return to the initial screen and click Change Job. Select "SG_CODIREN" and press the F3 key

 

Congratulations The new battery is installed and registered. Good use and good travels.